Exactly How to Set up a Tub
Exactly How to Set up a Tub
Blog Article
How do you feel with regards to Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately tough task. If the old bathtub is readily available, the project can move speedily; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will certainly require a helper to leave the old tub and set in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This article will certainly assist you set up a new tub in your restroom if you have actually currently purchased a brand-new bathtub and do not require to change the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any type of water staying in the system. The procedure of getting rid of the existing faucets can be rather troublesome as a result of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former kind must be attached to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Using both wooden boards under its feet, position the bathtub in the called for position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the bath tub until the level checks out degree.
To install faucets, fit all-time low of the furthest adaptable faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the other tap.
Activate the water supply and inspect all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been utilized at the very least once as this will resolve it into its final placement.
Preparing for the Setup
First of all, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the versatile faucet connectors to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, leading to complications with dampness and also feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can fracture rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our topic on How to Install a Bathtub. Thanks a lot for taking time to read our post. For those who liked our blog posting plz be sure to share it. Thank you for your time. Come back soon.
Book Today
Report this page